phone icon
Sales and Service
855 882 2886
basket icon
0 Items
$0.00
Find us on:
Main Categories

- Agilent Technologies / Varian
- Stokes Vacuum
- AJVS
- Thread Sealants
- Mounting Kits
- Leak Detectors
- Shipping Crates
- Cooling Water Circulators
- Laboratory Pipette Washers
- Laboratory Stirrers
- Muffle Furnace
- Rotary Evaporators
- Cold Traps
Category of products: Refurbished / Demo Industrial Dry Vacuum Pumps
- Agilent Technologies / Varian
- Stokes Vacuum
- AJVS
- Thread Sealants
- Mounting Kits
- Leak Detectors
- Shipping Crates
- Cooling Water Circulators
- Laboratory Pipette Washers
- Laboratory Stirrers
- Muffle Furnace
- Rotary Evaporators
- Cold Traps
Found 8 products
Item#: PN00263 Mfr Part#: Leyb-25P Manufacturer: Leybold
Price upon request

Leybold DRYVAC 25P (25-P) (25 P) Dry Vacuum Pump, 25p

 

Leybold DRYVAC 25P Overview:


The DRYVAC 25P, 50P and 100P are dry-compression vacuum pumps designed especially for semiconductor etching and CVD processes. Pump operating principle DRYVACs are four-stage hook-and-claw vacuum pumps.

 

Leybold DRYVAC 25P Operation:


The two rotors turn in opposite directions inside the pumping chamber . As they rotate, they open and close the intake (1/5) and outlet slots with each cycle.

The pumping chamber is divided by the rotors. Gas is drawn in on the one side of the rotors and compressed on the other side.

Suction and compression cycle: As the rotors rotate, the sealed space above the rotors is reduced in size and the gas is compressed. At the same time, the right rotor begins opening the inlet slot and gas is drawn into the pumping chamber below the rotors.

 

Leybold DRYVAC 25P Design:


There are four pumping stages located one above the other. The stages are pinned together.

The gas enters the pump through the intake port, is pumped through four pump stages, flows through an exhaust silencer, and through a non-return valve into the exhaust. The rotors are driven by two vertical shafts connected to the motor and synchronized by gears.The pumping chamber is free of sealants and lubricants; however , PFPE (perfluoropolyether) is used to lubricate the gearing and the lower bearings. The upper bearings are PFPE-grease lubricated. Piston rings are used to seal each shaft where it passes through the stages. The gear box is isolated from the pumping chamber by piston rings and radial shaft seals. The upper bearings are isolated by shaft seals. The bearings and seals are mounted in the water-cooled upper and lower end plates. The supply of cooling water is regulated by a thermostat. The pump stages are air cooled. The pump is fully enclosed by panels, which can easily be removed for maintenance purposes. An air outlet for cabinet ventilation is on the top of the DRY VAC.

Unit is fully rebuilt and comes with a FULL 12-MONTH WARRANTY!

 


A&J Vacuum Services offers full repair/service of Leybold 25P, along with all other brands offered on our website. AJVS also services Leybold turbo pumps and rotary vane pumps. Please contact us for information about our service and repair program or click http://www.ajvs.com/service.php to access our services page. We also offer emergency service upon request. For more information, please email A&J Vacuum Services at info@ajvs.com or call (973) 249-0854. Thank you for choosing AJVS as your supplier.


Condition: Remanufactured Call us for Availability
Item#: PN00264 Mfr Part#: Leyb-50P Manufacturer: Leybold
Price upon request

Leybold DRYVAC 50P (50-P) (50 P) Dry Vacuum Pump, 50p

 

Leybold DRYVAC 50P Overview:


The DRYVAC 25P, 50P and 100P are dry-compression vacuum pumps designed especially for semiconductor etching and CVD processes. Pump operating principle DRYVACs are four-stage hook-and-claw vacuum pumps.

 

Leybold DRYVAC 50P Operation:


The two rotors turn in opposite directions inside the pumping chamber . As they rotate, they open and close the intake (1/5) and outlet slots with each cycle.

The pumping chamber is divided by the rotors. Gas is drawn in on the one side of the rotors and compressed on the other side.

Suction and compression cycle: As the rotors rotate, the sealed space above the rotors is reduced in size and the gas is compressed. At the same time, the right rotor begins opening the inlet slot and gas is drawn into the pumping chamber below the rotors.

 

Leybold DRYVAC 50P Design:


There are four pumping stages located one above the other. The stages are pinned together.

The gas enters the pump through the intake port, is pumped through four pump stages, flows through an exhaust silencer, and through a non-return valve into the exhaust. The rotors are driven by two vertical shafts connected to the motor and synchronized by gears.The pumping chamber is free of sealants and lubricants; however , PFPE (perfluoropolyether) is used to lubricate the gearing and the lower bearings. The upper bearings are PFPE-grease lubricated. Piston rings are used to seal each shaft where it passes through the stages. The gear box is isolated from the pumping chamber by piston rings and radial shaft seals. The upper bearings are isolated by shaft seals. The bearings and seals are mounted in the water-cooled upper and lower end plates. The supply of cooling water is regulated by a thermostat. The pump stages are air cooled. The pump is fully enclosed by panels, which can easily be removed for maintenance purposes. An air outlet for cabinet ventilation is on the top of the DRY VAC.

Unit is fully rebuilt and comes with a FULL 12-MONTH WARRANTY!

 


A&J Vacuum Services offers full repair/service of Leybold 50P, along with all other brands offered on our website. AJVS also services Leybold turbo pumps and rotary vane pumps. Please contact us for information about our service and repair program or click http://www.ajvs.com/service.php to access our services page. We also offer emergency service upon request. For more information, please email A&J Vacuum Services at info@ajvs.com or call (973) 249-0854. Thank you for choosing AJVS as your supplier.


Condition: Remanufactured Call us for Availability
Item#: PN06869 Mfr Part#: 13800 Manufacturer: Leybold
Price upon request

Oerlikon / Leybold DryVac 25B Dry Vacuum Pump

 

Leybold DryVac 25B Overview:


The DRYVAC 25B is a dry-compression vacuum pumps designed especially for semiconductor etching and CVD processes. Pump operating principle DRYVACs are four-stage hook-and-claw vacuum pumps.

 

Leybold DryVac 25B Operation:


The two rotors turn in opposite directions inside the pumping chamber . As they rotate, they open and close the intake (1/5) and outlet slots with each cycle.

The pumping chamber is divided by the rotors. Gas is drawn in on the one side of the rotors and compressed on the other side.

Suction and compression cycle: As the rotors rotate, the sealed space above the rotors is reduced in size and the gas is compressed. At the same time, the right rotor begins opening the inlet slot and gas is drawn into the pumping chamber below the rotors.

 

Leybold DryVac 25B Design:


There are four pumping stages located one above the other. The stages are pinned together.

The gas enters the pump through the intake port, is pumped through four pump stages, flows through an exhaust silencer, and through a non-return valve into the exhaust. The rotors are driven by two vertical shafts connected to the motor and synchronized by gears.The pumping chamber is free of sealants and lubricants; however , PFPE (perfluoropolyether) is used to lubricate the gearing and the lower bearings. The upper bearings are PFPE-grease lubricated. Piston rings are used to seal each shaft where it passes through the stages. The gear box is isolated from the pumping chamber by piston rings and radial shaft seals. The upper bearings are isolated by shaft seals. The bearings and seals are mounted in the water-cooled upper and lower end plates. The supply of cooling water is regulated by a thermostat. The pump stages are air cooled. The pump is fully enclosed by panels, which can easily be removed for maintenance purposes. An air outlet for cabinet ventilation is on the top of the DRY VAC.

Unit is fully rebuilt and comes with a FULL 6-MONTH WARRANTY!


A&J Vacuum Services offers full repair/service of Edwards Vacuum Pumps, along with all other brands offered on our website. AJVS also services Edwards turbo pumps and rotary vane pumps. Please contact us for information about our service and repair program or click http://www.ajvs.com/service.php to access our services page. We also offer emergency service upon request. For more information, please email A&J Vacuum Services at info@ajvs.com or call (973) 249-0854. Thank you for choosing AJVS as your supplier.


Condition: Remanufactured Call us for Availability
Item#: PN06870 Mfr Part#: 25p Manufacturer: Leybold
Price upon request

Leybold / Oerlikon 25P (25-P) (25 P) Dry Vacuum Pump, 25p

 

Leybold / Oerlikon 25P Overview:


The DRYVAC 25P, 50P and 100P are dry-compression vacuum pumps designed especially for semiconductor etching and CVD processes. Pump operating principle DRYVACs are four-stage hook-and-claw vacuum pumps.

 

Leybold / Oerlikon 25P Operation:


The two rotors turn in opposite directions inside the pumping chamber . As they rotate, they open and close the intake (1/5) and outlet slots with each cycle.

The pumping chamber is divided by the rotors. Gas is drawn in on the one side of the rotors and compressed on the other side.

Suction and compression cycle: As the rotors rotate, the sealed space above the rotors is reduced in size and the gas is compressed. At the same time, the right rotor begins opening the inlet slot and gas is drawn into the pumping chamber below the rotors.

 

Leybold / Oerlikon 25P Design:


There are four pumping stages located one above the other. The stages are pinned together.

The gas enters the pump through the intake port, is pumped through four pump stages, flows through an exhaust silencer, and through a non-return valve into the exhaust. The rotors are driven by two vertical shafts connected to the motor and synchronized by gears.The pumping chamber is free of sealants and lubricants; however , PFPE (perfluoropolyether) is used to lubricate the gearing and the lower bearings. The upper bearings are PFPE-grease lubricated. Piston rings are used to seal each shaft where it passes through the stages. The gear box is isolated from the pumping chamber by piston rings and radial shaft seals. The upper bearings are isolated by shaft seals. The bearings and seals are mounted in the water-cooled upper and lower end plates. The supply of cooling water is regulated by a thermostat. The pump stages are air cooled. The pump is fully enclosed by panels, which can easily be removed for maintenance purposes. An air outlet for cabinet ventilation is on the top of the DRY VAC.

Unit is fully rebuilt and comes with a FULL 12-MONTH WARRANTY!

 


A&J Vacuum Services offers full repair/service of Leybold / Oerlikon 25P, along with all other brands offered on our website. AJVS also services Leybold / Oerlikon turbo pumps and rotary vane pumps. Please contact us for information about our service and repair program or click http://www.ajvs.com/service.php to access our services page. We also offer emergency service upon request. For more information, please email A&J Vacuum Services at info@ajvs.com or call (973) 249-0854. Thank you for choosing AJVS as your supplier.


Condition: Remanufactured Call us for Availability
Item#: PN06871 Mfr Part#: E13830 Manufacturer: Leybold
Price upon request

Leybold DryVac 50 B Dry Vacuum Pump, 200/208 VAC, 50/60 Hz, E13830

 

Leybold DryVac 50B Overview:


The DRYVAC 25P, 50P and 100P are dry-compression vacuum pumps designed especially for semiconductor etching and CVD processes. Pump operating principle DRYVACs are four-stage hook-and-claw vacuum pumps.

 

Leybold DryVac 50B Operation:


The two rotors turn in opposite directions inside the pumping chamber . As they rotate, they open and close the intake (1/5) and outlet slots with each cycle.

The pumping chamber is divided by the rotors. Gas is drawn in on the one side of the rotors and compressed on the other side.

Suction and compression cycle: As the rotors rotate, the sealed space above the rotors is reduced in size and the gas is compressed. At the same time, the right rotor begins opening the inlet slot and gas is drawn into the pumping chamber below the rotors.

 

Leybold DryVac 50B Design:


There are four pumping stages located one above the other. The stages are pinned together.

The gas enters the pump through the intake port, is pumped through four pump stages, flows through an exhaust silencer, and through a non-return valve into the exhaust. The rotors are driven by two vertical shafts connected to the motor and synchronized by gears.The pumping chamber is free of sealants and lubricants; however , PFPE (perfluoropolyether) is used to lubricate the gearing and the lower bearings. The upper bearings are PFPE-grease lubricated. Piston rings are used to seal each shaft where it passes through the stages. The gear box is isolated from the pumping chamber by piston rings and radial shaft seals. The upper bearings are isolated by shaft seals. The bearings and seals are mounted in the water-cooled upper and lower end plates. The supply of cooling water is regulated by a thermostat. The pump stages are air cooled. The pump is fully enclosed by panels, which can easily be removed for maintenance purposes. An air outlet for cabinet ventilation is on the top of the DRY VAC.

Unit is fully rebuilt and comes with a FULL 6-MONTH WARRANTY!


A&J Vacuum Services offers full repair/service of Edwards Vacuum Pumps, along with all other brands offered on our website. AJVS also services Edwards turbo pumps and rotary vane pumps. Please contact us for information about our service and repair program or click http://www.ajvs.com/service.php to access our services page. We also offer emergency service upon request. For more information, please email A&J Vacuum Services at info@ajvs.com or call (973) 249-0854. Thank you for choosing AJVS as your supplier.


Condition: Remanufactured Call us for Availability
Item#: PN06872 Mfr Part#: 50p Manufacturer: Leybold
Price upon request

Leybold / Oerlikon 50P (50-P) (50 P) Dry Vacuum Pump, 50p

 

Leybold / Oerlikon 50P Overview:


The DRYVAC 25P, 50P and 100P are dry-compression vacuum pumps designed especially for semiconductor etching and CVD processes. Pump operating principle DRYVACs are four-stage hook-and-claw vacuum pumps.

 

Leybold / Oerlikon 50P Operation:


The two rotors turn in opposite directions inside the pumping chamber . As they rotate, they open and close the intake (1/5) and outlet slots with each cycle.

The pumping chamber is divided by the rotors. Gas is drawn in on the one side of the rotors and compressed on the other side.

Suction and compression cycle: As the rotors rotate, the sealed space above the rotors is reduced in size and the gas is compressed. At the same time, the right rotor begins opening the inlet slot and gas is drawn into the pumping chamber below the rotors.

 

Leybold / Oerlikon 50P Design:


There are four pumping stages located one above the other. The stages are pinned together.

The gas enters the pump through the intake port, is pumped through four pump stages, flows through an exhaust silencer, and through a non-return valve into the exhaust. The rotors are driven by two vertical shafts connected to the motor and synchronized by gears.The pumping chamber is free of sealants and lubricants; however , PFPE (perfluoropolyether) is used to lubricate the gearing and the lower bearings. The upper bearings are PFPE-grease lubricated. Piston rings are used to seal each shaft where it passes through the stages. The gear box is isolated from the pumping chamber by piston rings and radial shaft seals. The upper bearings are isolated by shaft seals. The bearings and seals are mounted in the water-cooled upper and lower end plates. The supply of cooling water is regulated by a thermostat. The pump stages are air cooled. The pump is fully enclosed by panels, which can easily be removed for maintenance purposes. An air outlet for cabinet ventilation is on the top of the DRY VAC.

Unit is fully rebuilt and comes with a FULL 12-MONTH WARRANTY!

 


A&J Vacuum Services offers full repair/service of Leybold / Oerlikon 50P, along with all other brands offered on our website. AJVS also services Leybold / Oerlikon turbo pumps and rotary vane pumps. Please contact us for information about our service and repair program or click http://www.ajvs.com/service.php to access our services page. We also offer emergency service upon request. For more information, please email A&J Vacuum Services at info@ajvs.com or call (973) 249-0854. Thank you for choosing AJVS as your supplier.


Condition: Remanufactured Call us for Availability
Item#: PN06873 Mfr Part#: 100b Manufacturer: Leybold
Price upon request

Leybold / Oerlikon 100B (100-B) (100 B) Dry Vacuum Pump, 100b

 

Leybold / Oerlikon 100B Overview:


The DRYVAC 25P, 50P and 100P are dry-compression vacuum pumps designed especially for semiconductor etching and CVD processes. Pump operating principle DRYVACs are four-stage hook-and-claw vacuum pumps.

 

Leybold / Oerlikon 100B Operation:


The two rotors turn in opposite directions inside the pumping chamber . As they rotate, they open and close the intake (1/5) and outlet slots with each cycle.

The pumping chamber is divided by the rotors. Gas is drawn in on the one side of the rotors and compressed on the other side.

Suction and compression cycle: As the rotors rotate, the sealed space above the rotors is reduced in size and the gas is compressed. At the same time, the right rotor begins opening the inlet slot and gas is drawn into the pumping chamber below the rotors.

 

Leybold / Oerlikon 100B Design:


There are four pumping stages located one above the other. The stages are pinned together.

The gas enters the pump through the intake port, is pumped through four pump stages, flows through an exhaust silencer, and through a non-return valve into the exhaust. The rotors are driven by two vertical shafts connected to the motor and synchronized by gears.The pumping chamber is free of sealants and lubricants; however , PFPE (perfluoropolyether) is used to lubricate the gearing and the lower bearings. The upper bearings are PFPE-grease lubricated. Piston rings are used to seal each shaft where it passes through the stages. The gear box is isolated from the pumping chamber by piston rings and radial shaft seals. The upper bearings are isolated by shaft seals. The bearings and seals are mounted in the water-cooled upper and lower end plates. The supply of cooling water is regulated by a thermostat. The pump stages are air cooled. The pump is fully enclosed by panels, which can easily be removed for maintenance purposes. An air outlet for cabinet ventilation is on the top of the DRY VAC.

Unit is fully rebuilt and comes with a FULL 12-MONTH WARRANTY!

 


A&J Vacuum Services offers full repair/service of Leybold / Oerlikon 100B, along with all other brands offered on our website. AJVS also services Leybold / Oerlikon turbo pumps and rotary vane pumps. Please contact us for information about our service and repair program or click http://www.ajvs.com/service.php to access our services page. We also offer emergency service upon request. For more information, please email A&J Vacuum Services at info@ajvs.com or call (973) 249-0854. Thank you for choosing AJVS as your supplier.


Condition: Remanufactured Call us for Availability
Item#: PN06874 Mfr Part#: 100p Manufacturer: Leybold
Price upon request

Leybold / Oerlikon 100P (100-P) (100 P) Dry Vacuum Pump, 100p

 

Leybold / Oerlikon 100P Overview:


The DRYVAC 25P, 50P and 100P are dry-compression vacuum pumps designed especially for semiconductor etching and CVD processes. Pump operating principle DRYVACs are four-stage hook-and-claw vacuum pumps.

 

Leybold / Oerlikon 100P Operation:


The two rotors turn in opposite directions inside the pumping chamber . As they rotate, they open and close the intake (1/5) and outlet slots with each cycle.

The pumping chamber is divided by the rotors. Gas is drawn in on the one side of the rotors and compressed on the other side.

Suction and compression cycle: As the rotors rotate, the sealed space above the rotors is reduced in size and the gas is compressed. At the same time, the right rotor begins opening the inlet slot and gas is drawn into the pumping chamber below the rotors.

 

Leybold / Oerlikon 100P Design:


There are four pumping stages located one above the other. The stages are pinned together.

The gas enters the pump through the intake port, is pumped through four pump stages, flows through an exhaust silencer, and through a non-return valve into the exhaust. The rotors are driven by two vertical shafts connected to the motor and synchronized by gears.The pumping chamber is free of sealants and lubricants; however , PFPE (perfluoropolyether) is used to lubricate the gearing and the lower bearings. The upper bearings are PFPE-grease lubricated. Piston rings are used to seal each shaft where it passes through the stages. The gear box is isolated from the pumping chamber by piston rings and radial shaft seals. The upper bearings are isolated by shaft seals. The bearings and seals are mounted in the water-cooled upper and lower end plates. The supply of cooling water is regulated by a thermostat. The pump stages are air cooled. The pump is fully enclosed by panels, which can easily be removed for maintenance purposes. An air outlet for cabinet ventilation is on the top of the DRY VAC.

Unit is fully rebuilt and comes with a FULL 12-MONTH WARRANTY!

 


A&J Vacuum Services offers full repair/service of Leybold / Oerlikon 100P, along with all other brands offered on our website. AJVS also services Leybold / Oerlikon turbo pumps and rotary vane pumps. Please contact us for information about our service and repair program or click http://www.ajvs.com/service.php to access our services page. We also offer emergency service upon request. For more information, please email A&J Vacuum Services at info@ajvs.com or call (973) 249-0854. Thank you for choosing AJVS as your supplier.


Condition: Remanufactured Call us for Availability
Contact
address
A&J Vacuum Services
16 Somerset Place, Clifton, NJ 07012
customer service
Customer Service
Phone: 973-249-0854, Fax: 973-249-0855
working hours
Service Hours
8:00am to 5:00pm, Monday thru Friday EST
All trademarks, trade names or logons mentioned or used are the property of their respective owners.